VTXPITMODE changes when disabling and enabling ANGLE mode

[IvoFPV]

I was just testing my build today hovering with angle mode and disabled and enabled it a couple of times and after that I checked blackbox logs and it shows that every time when I did that, VTXPITMODE was also disabled or enabled. Pit mode is not assigned in modes tab. Running BF 3.5.5 on this quad, using latest log viewer 3.3.1

LOG00023.zip

diff

version

Betaflight / MATEKF405 (MKF4) 3.5.5 Jan 15 2019 / 10:05:36 (88921670b) MSP API: 1.40

board_name MATEKF405
manufacturer_id

name

name Ivo

resources

resource MOTOR 5 NONE
resource SERIAL_TX 11 A15

mixer

servo

servo mix

feature

feature AIRMODE

beeper

beacon

map

map TAER1234

serial

serial 4 2048 115200 57600 0 115200
serial 30 32 115200 57600 0 115200

led

color

mode_color

aux

aux 0 0 0 1200 2100 0 0
aux 1 1 0 1200 1600 0 0
aux 2 13 1 1800 2100 0 0
aux 3 26 0 1200 2100 0 0
aux 4 35 1 1300 1700 0 0

adjrange

rxrange

rxrange 0 987 2011
rxrange 1 987 2011
rxrange 2 987 2011
rxrange 3 987 2011

vtx

rxfail

master

set mag_hardware = NONE
set baro_hardware = NONE
set min_check = 1010
set max_check = 1990
set rssi_channel = 8
set rc_smoothing_type = FILTER
set blackbox_p_ratio = 64
set motor_pwm_protocol = DSHOT600
set bat_capacity = 1300
set vbat_min_cell_voltage = 34
set vbat_warning_cell_voltage = 36
set small_angle = 180
set gps_provider = UBLOX
set gps_rescue_angle = 35
set gps_rescue_initial_alt = 25
set gps_rescue_descent_dist = 80
set gps_rescue_ground_speed = 1000
set gps_rescue_sanity_checks = RESCUE_SANITY_OFF
set gps_rescue_min_sats = 0
set pid_process_denom = 1
set osd_warn_core_temp = OFF
set osd_rssi_alarm = 50
set osd_cap_alarm = 1000
set osd_vbat_pos = 2466
set osd_rssi_pos = 2381
set osd_tim_1_pos = 471
set osd_tim_2_pos = 2519
set osd_flymode_pos = 2145
set osd_throttle_pos = 2487
set osd_vtx_channel_pos = 2168
set osd_crosshairs_pos = 2285
set osd_ah_sbar_pos = 238
set osd_ah_pos = 2158
set osd_current_pos = 2475
set osd_mah_drawn_pos = 2508
set osd_gps_speed_pos = 227
set osd_gps_sats_pos = 153
set osd_home_dir_pos = 108
set osd_home_dist_pos = 110
set osd_altitude_pos = 246
set osd_pidrate_profile_pos = 129
set osd_warnings_pos = 2409
set osd_avg_cell_voltage_pos = 2498
set osd_battery_usage_pos = 40
set osd_disarmed_pos = 2443
set osd_core_temp_pos = 2202
set osd_stat_max_spd = OFF
set osd_stat_endbatt = ON
set osd_stat_bbox = OFF
set debug_mode = GYRO_SCALED
set vtx_band = 5
set vtx_channel = 2
set vtx_freq = 5695
set rcdevice_init_dev_attempts = 4

profile

profile 0

set dterm_notch_cutoff = 0
set anti_gravity_gain = 7000
set feedforward_transition = 15
set iterm_relax = RP
set p_pitch = 47
set i_pitch = 55
set d_pitch = 34
set f_pitch = 100
set p_roll = 47
set i_roll = 55
set d_roll = 31
set f_roll = 100
set p_yaw = 40
set i_yaw = 120
set f_yaw = 100

rateprofile

rateprofile 0

set roll_rc_rate = 192
set pitch_rc_rate = 192
set yaw_rc_rate = 192
set roll_expo = 25
set pitch_expo = 25
set yaw_expo = 20
set roll_srate = 64
set pitch_srate = 64
set yaw_srate = 50

[McGiverGim]

It seems that the info of mode changes is stored in a 32 bit variable, as flags. But the list of modes are bigger than 32, so it is overflowing and detecting modes that does not exist.
I think this first needs to be fixed in the firmware part, and then read it accordingly here.

[chupocro]

Similar here. When I switch from angle to horizon mode the log viewer shows: Flight Mode Change | ANGLE OFF | HORIZON ON | VTXPITMODE OFF | USER1 ON. When switching from horizon to acro mode it says: Flight Mode Change | HORIZON OFF | USER1 OFF. Going back to horizon mode it says: Flight Mode Change | HORIZON ON | USER1 ON and when returning back to angle mode it says: Flight Mode Change | ANGLE ON | HORIZON OFF | VTXPITMODE ON | USER1 OFF.

I don't have assigned anything for VTX Pit Mode or USER1. Running Betaflight 3.5.0 and log viewer 3.3.1

[McGiverGim]

The flight modes over 32 give this strange behavior, they are not supported.