HOTFIX: add file that was missed from KAFKA-17048 commit

config/kraft/reconfig-server.properties

@@ -0,0 +1,132 @@
+# Licensed to the Apache Software Foundation (ASF) under one or more
+# contributor license agreements.  See the NOTICE file distributed with
+# this work for additional information regarding copyright ownership.
+# The ASF licenses this file to You under the Apache License, Version 2.0
+# (the "License"); you may not use this file except in compliance with
+# the License.  You may obtain a copy of the License at
+#
+#    http://www.apache.org/licenses/LICENSE-2.0
+#
+# Unless required by applicable law or agreed to in writing, software
+# distributed under the License is distributed on an "AS IS" BASIS,
+# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+# See the License for the specific language governing permissions and
+# limitations under the License.
+
+#
+# This configuration file is intended for use in KRaft mode, where
+# Apache ZooKeeper is not present.
+#
+
+############################# Server Basics #############################
+
+# The role of this server. Setting this puts us in KRaft mode
+process.roles=broker,controller
+
+# The node id associated with this instance's roles
+node.id=1
+
+# List of controller endpoints used connect to the controller cluster
+controller.quorum.bootstrap.servers=localhost:9093
+
+############################# Socket Server Settings #############################
+
+# The address the socket server listens on.
+# Combined nodes (i.e. those with `process.roles=broker,controller`) must list the controller listener here at a minimum.
+# If the broker listener is not defined, the default listener will use a host name that is equal to the value of java.net.InetAddress.getCanonicalHostName(),
+# with PLAINTEXT listener name, and port 9092.
+#   FORMAT:
+#     listeners = listener_name://host_name:port
+#   EXAMPLE:
+#     listeners = PLAINTEXT://your.host.name:9092
+listeners=PLAINTEXT://:9092,CONTROLLER://:9093
+
+# Name of listener used for communication between brokers.
+inter.broker.listener.name=PLAINTEXT
+
+# Listener name, hostname and port the broker or the controller will advertise to clients.
+# If not set, it uses the value for "listeners".
+advertised.listeners=PLAINTEXT://localhost:9092,CONTROLLER://localhost:9093
+
+# A comma-separated list of the names of the listeners used by the controller.
+# If no explicit mapping set in `listener.security.protocol.map`, default will be using PLAINTEXT protocol
+# This is required if running in KRaft mode.
+controller.listener.names=CONTROLLER
+
+# Maps listener names to security protocols, the default is for them to be the same. See the config documentation for more details
+listener.security.protocol.map=CONTROLLER:PLAINTEXT,PLAINTEXT:PLAINTEXT,SSL:SSL,SASL_PLAINTEXT:SASL_PLAINTEXT,SASL_SSL:SASL_SSL
+
+# The number of threads that the server uses for receiving requests from the network and sending responses to the network
+num.network.threads=3
+
+# The number of threads that the server uses for processing requests, which may include disk I/O
+num.io.threads=8
+
+# The send buffer (SO_SNDBUF) used by the socket server
+socket.send.buffer.bytes=102400
+
+# The receive buffer (SO_RCVBUF) used by the socket server
+socket.receive.buffer.bytes=102400
+
+# The maximum size of a request that the socket server will accept (protection against OOM)
+socket.request.max.bytes=104857600
+
+
+############################# Log Basics #############################
+
+# A comma separated list of directories under which to store log files
+log.dirs=/tmp/kraft-combined-logs
+
+# The default number of log partitions per topic. More partitions allow greater
+# parallelism for consumption, but this will also result in more files across
+# the brokers.
+num.partitions=1
+
+# The number of threads per data directory to be used for log recovery at startup and flushing at shutdown.
+# This value is recommended to be increased for installations with data dirs located in RAID array.
+num.recovery.threads.per.data.dir=1
+
+############################# Internal Topic Settings  #############################
+# The replication factor for the group metadata internal topics "__consumer_offsets" and "__transaction_state"
+# For anything other than development testing, a value greater than 1 is recommended to ensure availability such as 3.
+offsets.topic.replication.factor=1
+transaction.state.log.replication.factor=1
+transaction.state.log.min.isr=1
+
+############################# Log Flush Policy #############################
+
+# Messages are immediately written to the filesystem but by default we only fsync() to sync
+# the OS cache lazily. The following configurations control the flush of data to disk.
+# There are a few important trade-offs here:
+#    1. Durability: Unflushed data may be lost if you are not using replication.
+#    2. Latency: Very large flush intervals may lead to latency spikes when the flush does occur as there will be a lot of data to flush.
+#    3. Throughput: The flush is generally the most expensive operation, and a small flush interval may lead to excessive seeks.
+# The settings below allow one to configure the flush policy to flush data after a period of time or
+# every N messages (or both). This can be done globally and overridden on a per-topic basis.
+
+# The number of messages to accept before forcing a flush of data to disk
+#log.flush.interval.messages=10000
+
+# The maximum amount of time a message can sit in a log before we force a flush
+#log.flush.interval.ms=1000
+
+############################# Log Retention Policy #############################
+
+# The following configurations control the disposal of log segments. The policy can
+# be set to delete segments after a period of time, or after a given size has accumulated.
+# A segment will be deleted whenever *either* of these criteria are met. Deletion always happens
+# from the end of the log.
+
+# The minimum age of a log file to be eligible for deletion due to age
+log.retention.hours=168
+
+# A size-based retention policy for logs. Segments are pruned from the log unless the remaining
+# segments drop below log.retention.bytes. Functions independently of log.retention.hours.
+#log.retention.bytes=1073741824
+
+# The maximum size of a log segment file. When this size is reached a new log segment will be created.
+log.segment.bytes=1073741824
+
+# The interval at which log segments are checked to see if they can be deleted according
+# to the retention policies
+log.retention.check.interval.ms=300000

config/kraft/server.properties

@@ -26,9 +26,7 @@ process.roles=broker,controller
 # The node id associated with this instance's roles
 node.id=1
 
-# Information about the KRaft controller quorum.
-# Uncomment controller.quorum.voters to use a static controller quorum.
-#controller.quorum.voters=1@localhost:9093
+# The connect string for the controller quorum
 controller.quorum.voters=1@localhost:9093
 
 ############################# Socket Server Settings #############################

docs/quickstart.html

@@ -56,10 +56,10 @@ <h6>Using downloaded files</h6>
         <pre><code class="language-bash">$ KAFKA_CLUSTER_ID="$(bin/kafka-storage.sh random-uuid)"</code></pre>
 
         <p>Format Log Directories</p>
-        <pre><code class="language-bash">$ bin/kafka-storage.sh format --standalone -t $KAFKA_CLUSTER_ID -c config/kraft/server.properties</code></pre>
+        <pre><code class="language-bash">$ bin/kafka-storage.sh format --standalone -t $KAFKA_CLUSTER_ID -c config/kraft/reconfig-server.properties</code></pre>
 
         <p>Start the Kafka Server</p>
-        <pre><code class="language-bash">$ bin/kafka-server-start.sh config/kraft/server.properties</code></pre>
+        <pre><code class="language-bash">$ bin/kafka-server-start.sh config/kraft/reconfig-server.properties</code></pre>
 
         <p>Once the Kafka server has successfully launched, you will have a basic Kafka environment running and ready to use.</p>